ELTRON TLP 2046 DRIVER FOR MAC DOWNLOAD

Page 41 Operation Label Variations Your TLP is equipped with a sensor ca- pable of detecting the gap between labels while and the they are being printed. Page 66 Windows Printer Driver Rev. The printer will feed a single label each time the FEED button is depressed. Press the Feed button with the printhead closed, as needed, to sup- ply more label stock ribbon. Page 6 Rev. Follow the installation instructions on the screen to install the software.

Uploader: Tudal
Date Added: 21 September 2012
File Size: 57.43 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 54375
Price: Free* [*Free Regsitration Required]

Press the Feed button with the printhead closed, as needed, to sup- ply more label stock ribbon.

The printer driver is installed and ap- pears in the Installed Printers list in the Printers sltron box. Eltron tlp 2046 the Replacement Step 3 casing top cover off.

Impresoras Etiquetas Codigos Barras – MaxiOUTLETS

Swing eltron tlp 2046 bracket down. Page 46 Operation Battery Replace the battery by lifting the battery retain- ing clip eltron tlp 2046 and inserting the new battery in with Replacement Step 4 the printed side up. Attach the ribbon to the rewind core fiberboard tube on the ribbon take-up tube with tape. Listed below are barcode printers and barcode printer family drivers supported by Loftware. Technical Support, Copyright Notice Eltron International Incorporated and may not be duplicated in full or in eltroj by any person without eltron tlp 2046 approval from Eltron.

Don’t show me this message again. Warranty Information, Fcc Notice 12 months from the date of purchase by the end user. Figure Attaching Ribbon Tape Table Of Contents Introduction Page 23 Operation Label Hlp Open the top and right side cover on eotron printer.

Got it, continue to print.

Page 6 Rev. This manual also for: Refer to Appendix B for complete supplies ordering information. Trouble Shooting Guide 2.

Loftware Barcode Printing software supports the following Printer Family Elteon and the specific label printer manufacturers families who support the associated language or emulation. When printing large labels or labels with a lot of information near the right edge, a slower eltron tlp 2046 speed will avoid pauses while eltron tlp 2046 caused by buffer under-run. Releasing the lever allows it to snap back.

Supported Labeling Printers

Comments to this Manuals Your Name. Operation Label The printer can be set up to automatically rewind labels into a roll or in a label dispense Rewinding and mode, single peeled label. Check for Out-of-Media eltron tlp 2046 or missing labels tllp the middle of a roll. Don’t have an account?

Eltron warrants the printhead, under normal use and service, to be free from defects eltron tlp 2046 material and workmanship for elrron period of ninety 90 days from the date of purchase by the end user. Page 61 Accessories Rev. See Figures and Elttron your printer or printer language is not listed here, please call Fold the label liner over the clip to the back of the printer. Eltron tlp 2046 battery may explode causing damage or injury. Ensure that Print Configuration Control switch setting match the print mode.

Save this screw for mounting and storing the bracket. Getting Started Figure Removal and Insertion of the Memory Cartridge Insert the memory cartridge into the cartridge slot, label side towards the center of the printer.

Introduction This section provides information on the instal- lation of the TLP printer and software. Operation Label Loading Adjust the label pressure control knob to match Step 8 the label stock in use. Possible problem with label stock. Operation Label Loading Open the Printhead Assembly by pushing the release lever to the right, towards the back of Step the printer. Operation Loading Labels Your TLP can print on continuous direct thermal paper, direct thermal adhesive backed or Tags labels or eltron tlp 2046 tags.

Lift To Open Remove the tape securing the eltron tlp 2046 rewind clip to the eltron tlp 2046 rewind tube. This section provides information on the instal- lation of the TLP printer and software.

Figure Electrical Outlet Insert Page 60 Accessories Rev. For tags, see Figure A To print the manual completely, please, download it. Windows Printer Driver Paper Quality, The print speed can be adjusted to compensate for manufacturing differences in label stock. The TLP has a 4 inch print width, dpi print eltron tlp 2046 and up to KB user config- urable memory. It prints in both direct thermal and thermal transfer mode.

Supported Barcode Printers

Eltron tlp 2046 17 Getting Started Step 4 The printer has a manual configuration switch bank located on the back panel of the printer. Getting Started Step Parallel Interface Attach a eltrron parallel printer cable from the Attach Interface computer to the Centronics interface connector Cable at the back of the printer.

Page 48 Operation Rev. Place this switch in the OFF 0 position to remove power when you have finished using your printer. Label Rewinding And Auto-dispensing Operation Label Eltron tlp 2046 printer can be set up to automatically rewind labels into a e,tron or in a label dispense Rewinding and mode, single peeled label. Page of 68 Go.

Rate this post

Leave a Reply

Your email address will not be published. Required fields are marked *

Solve : *
3 × 4 =